sb1m widget

Kumpulan soal interview untuk teknisi instrument

Artikel ini berisi kumpulan soal-soal test masuk kerja untuk posisi TEKNISI INSTRUMENT pada pabrik kimia, petrokimia dan oil and gas industri. Pada umumnya  testing masuk kerja  di pabrik besar dilaksanakan dengan menggunakan bahasa ingris sebagai bahasa pengantarnya, hal ini tidak lain karena dalam pekerjaan rutinnya pegawai yang bekerja di pabrik sejenis ini akan menjumpai  petunjuk-petunjuk dan prosedur dalam bahasa inggris, alasan kuat lainnya karena mesin-mesin industri yang dipergunakan di pabrik kimia, di pabrik petrokimia dan di pabrik oil and gas diproduksi oleh pabriknya untuk dipasarkan secara global sehingga tidak heran bila mereka pembuat mesin atau alat-alat pabrik mengeluarkan dokumen yang berkaitan dengan mesin tersebut dalam  bahasa international.

Sebenarnya ada manfaat positip dari proses penerimaan pegawai dengan wawancara dalam bahasa inggris seperti ini, yaitu para peserta test jadi terpacu untuk belajar meningkatkan penguasaan bahasanya,  alih-alih dari penguasaan bahasa yang baik untuk selanjutnya jika yang bersangkutan berminat untuk melamar pekerjaan ke luar negeri sudah memiliki bekal bahasa yang baik sehingga dapat berkompetisi dengan pelamar dari negara lain. Materi soal-soal ini diambil dari pengalaman pribadi penulis ketika mengikuti seleksi penerimaan pegawai di dalam negeri maupun di luar negeri. Jika ada jawaban soal yang kurang dapat dicerna penjelasannya, silahkan temukan artikel terkait yang ada di blog ini, jika masih memerlukan penjelasan lanjutan bisa menulis komen pada bagian akhir artikel untuk mendapat jawaban langsung dari kami.

Question and Answer for Instrument Technician Post:

  1. Explain the application of proportional integral and derivative action

Proportional control only:
Proportional control only attempts to return a measurement to the set point after a load upset has occurred. However it is impossible for a proportional controller to return the measurement exactly to the set point.
Use: It is normally used for level controls. It reduces the effect of a load change but it cannot eliminate it.
Proportional plus reset control:
Reset action is introduced to eliminate offset. It will integrate any difference between measurement and set point and cause the controller’s output to change until the difference between the measurement and set point is zero. Reset will act as long as the error exists.
Use: Proportional + Reset controllers are by far the common types used in industrial process control and where predominate dead times occur.
Proportional plus reset plus derivative:
Derivative or rate action helps the controller overcome system inertia and result in faster, more precise control. Derivative action occurs whenever the measurement signal changes. Under study conditions the rate action does not act. Derivative allows the controller to inject more corrective action.
Use: On temperature control

  1. Explain the working of a turbine meter.

Turbine meters consist of a straight flow tube within which a turbine or fan is free to rotate, about its axis which is fixed along the center line of the tube. Straightening vanes upstream of the turbine minimizes possible rotational components of fluid flow. In most units a magnetic pick-up system senses the rotation of the rotor through the tube wall. The turbine meter is a flow rate device, since the rotor speed is directly proportional to flow rate. The output is usually in the form of electrical pulses from the magnetic pick-up with a frequency proportional to flow rate. Turbine meter are primarily applied to measurement of clean and non-corrosive hydrocarbons.

  1. What are the primary elements for measuring pressure?

The primary elements used for measuring pressure are:

  • Bourdon tube.
  • Diapraghm
  • Capsules
  • Bellows
  • Pressure Springs.

Bourdon: The elastic deformation pressure elements such as spiral, helix or type C bourdon.
Diaphragm: The diaphragm is best suited for low pressure measurement.
Capsules     : Two circular diaphragms are welded together to form a pressure capsule.
Bellows       : Bellows is a one – piece, collapsible, seamless metallic unit with deep folds formed from      very tin walled tubing.
Pressure spring: Pressure springs of helical or spiral shape used for measuring high pressures.

Silahkan download kumpulan soal-soal Test tertulis untuk Teknisi Instrumentasi dibawah ini:

Soal Test Tulis Instrumentasi-1
Soal Test Tulis Instrumentasi-2
Soal Test Tulis Instrumentasi-3




Leave a Reply

Your email address will not be published. Required fields are marked *